Wall Plates

DataComm Recessed Bulk Cable Plate

Use DataComm Electronics recessed low voltage cable plates to install low voltage cables behind your flat panel TV, your amplifier or other audio/video devices. These recessed bulk cable plates are designed to be used with low voltage mounting plate brackets by any major manufacturer.

The recessed low voltage cable plates can be installed upright or upside down. Install the 45-0001/2 upside down when installing flat panel TV’s.

Determine the location of your flat panel TV, amplifier or audio/video device. Cut a hole in the wall and install the low voltage mounting plate bracket. Then simply pull your cables through the mounted low voltage mounting plate bracket and then through the DataComm Electronics recessed low voltage cable plate. Insert the DataComm Electronics recessed low voltage cable plate into your mounted low voltage mounting plate bracket and secure tightly with the wall plate screws.

DataComm  1-3/4 Inch Hole Saw Plate

This two-by-two-inch wall plate is designed to conceal low voltage cables behind the smaller home theater and security equipment. The compact design mounts inside a 1-3/4 inch hole and features a 0.77 x 0.87-inch brush opening. Built-in wings enable mounting without the need for a low voltage mounting bracket. Simply tighten the screws into place for a secure hold.

DataComm Bulk Cable Wall Plate with Flex

DataComm's patented flex bulk cable wall plate provides an easy and convenient way to organize your cables while keeping a clean look to your install. It allows you to pass low voltage cables through the wall, behind your flat panel TV, amp, or other audio/video devices.

The center of the cable plate is made of a flexible plastic, which allows you to pass multiple cables (up to six) through the plate. The attached mounting wings fit snugly against any wall up to 1" thick and eliminate the need for an additional low voltage bracket.

DataComm Décor Insert

Flex Cable Insert

DataComm’s 45-0016-WH Decor Insert is designed for use with Decor and Decora-style wall plates. These bulk inserts allow you to pull a variety of cables straight through at the beginning or end of a wire run, saving time and eliminating an extra connection at the wall. A sheet of thin flexible plastic conceals the cut-in opening and helps prevent dust and other debris from entering your stud bay. The star-style slit can easily accommodate up to four cables including HDMI, coax, and Ethernet. With a low profile and multiple angles of exit, the 45-0016-WH is great behind ultra-slim TV mounts, in entertainment closets, or anywhere else space is limited.

With a durable finish and a simple installation process, the 45-0016-WH is a versatile solution for networking and home theater cable runs. Decor wall plates come in two parts: the face plate and the insert. Using this system, you can mix and match inserts for the combination plate of your dreams. FireFold carries one, two, and three-gang Decora faceplates for use with this bulk pass-through as well as a wide variety of other inserts. To assemble, just attach this insert to your face plate then secure the face plate to a low voltage box or bracket.

Note: Decor faceplate sold separately.

DataComm 45-0021-WH Bulk Cable Plate

Use DataComm Electronics’ patented new recessed low voltage cable plate with recessed power to install power and low voltage cables behind your flat panel TV, your amplifier or other audio and video devices. The 45-0021 recessed low voltage cable plate with recessed power can be installed upright or upside down.

Use either a single gang retrofit work box or for new construction installations, use a new nail on box. Once you have wired the receptacle*, then begin by inserting the receptacle portion of the plate into the work box. Once the entire recessed plate is flush to the wall, using the two white screws supplied, screw the receptacle portion of the plate to the work box. Next, screw down the screws with wings. These wings will fasten tightly against the back of the drywall. Plug in all necessary video and audio cables. Install your flat panel TV mounting bracket per the flat panel TV bracket manufacturer’s instructions.

DataComm 45-0031-WH Bulk Cable Plate

DataComm Electronics' new, patented Recessed Low Voltage Media Plates offer the convenience of a duplex receptacle and a recessed plate with enough room to store the low voltage cables behind your flat panel TV.

DataComm 45-0008-WH Bulk Cable Plate

Use the Easy Mount Recessed Low Voltage Cable Plate to install low voltage cables behind your flat panel TV, your amplifier, or other audio and video devices. The wall plate can be installed upright or upside down.

This plate's innovative "mounting wings" eliminate the need for a low voltage mounting bracket. The mounting wings are molded into the Easy Mount wall plate and fasten tightly against the back of the drywall. The standard Easy Mount Cable Plate has the capacity of a double gang plate in a single gang profile.

The new, thinner profile of the Easy Mount Cable Plate is designed to fit behind the industry's thinnest mounts and flat-panel TVs.

DataComm 45-0041-WH Recessed Low Volt Plate

The patented Recessed Low Voltage Media Plate with Duplex Receptacle/Duplex Surge Suppressor offers the convenience of a duplex receptacle and a recessed plate with enough room to store low voltage cables behind your flat panel TV. This box is available in surge and 20 amp commercial-grade models.

DataComm 45-0009-WH Bulk Cable Plate

Use the Easy Mount Recessed Low Voltage Cable Plate to install low voltage cables behind your flat panel TV, your amplifier, or other audio and video devices. The wall plate can be installed upright or upside down.

This plate's innovative "mounting wings" eliminate the need for a low voltage mounting bracket. The mounting wings are molded into the Easy Mount wall plate and fasten tightly against the back of the drywall. The standard Easy Mount Cable Plate has the capacity of a double gang plate in a single gang profile.

The new, thinner profile of the Easy Mount Cable Plate is designed to fit behind the industry's thinnest mounts and flat-panel TVs.

The Slim-Fit version of the Easy Mount Recessed Cable Plate is designed for use in concrete wall applications where the wall cavity is 3/4" to 1" in depth.

Datacomm Recessed Pro-Power Kit

The Datacomm 45-0023-WH Recessed Pro-Power Kit with Straight Blade Inlet allows you to conceal power and other low voltage cables behind your HDTV by running them through the wall.

Package Includes

• (1) Recessed Cable Plate with Straight Blade Inlet
• (1) Recessed Cable Plate with Power
• (1) 6ft 16/2 w/Ground Extension Cord
• (1) Electrical Outlet Boxes
• (3) Wire Nuts

DataComm Recessed Receptacle

The patented DataComm 45-0024-WH Recessed Pro-Power Kit is an easy-to-install solution for hiding power and audio/video cables behind an HDTV. A duplex receptacle provides power for up to two devices, while a straight blade inlet provides organized cable routing. A flexible serrated screen on the interior of the straight blade inlet keeps cables securely routed.

DataComm Recessed Pro-Power Kit with Surge Suppressor

The patented DataComm 45-0024-WH Recessed Pro-Power Kit is an easy-to-install solution for hiding power and audio/video cables behind an HDTV. A duplex surge supressor receptacle provides power for up to two devices, while a straight blade inlet provides organized cable routing. A flexible serrated screen on the interior of the straight blade inlet keeps cables securely routed.

DataComm Décor Duplex 4.0 Amp USB Charger

The Décor Duplex 4.0A USB Charger is designed to quickly and easily replace existing outlets allowing you to charge multiple devices at once without sacrificing power outlets. Simply connect the USB end of your device’s charging cable into either of the USB ports, then connect the charging end of the cable to your smartphone, tablet, or other device.

DataComm Remote Device Mount, 62-5440

DataComm Electronics’ Remote Device Mount is used to mount HVAC and security sensors. Complete your project with a clean installation when the sensor is flush to the dry wall.

This is the simplest way to install a sensor. With this product there is no need to fish out wires from behind drywall, so say goodbye to fishing for wires from behind drywall!

The Remote Device Mount also comes with five different sensor inserts that will fit most brands of all sensor types: security, temperature and HVAC sensors to name a few.

DataComm Recessed Media Box w/ Duplex Receptacle

The Recessed Media Box II is designed to streamline power and cable management behind your HDTV. The box features a side cover plate with knockouts for conduit or tube. This is the ideal solution for allowing your TV or other display to be mounted flush to the wall. This box is available in surge and 20 commercial-grade models.

Expandable Media Box w/ 15 Amp/125 Volt Duplex Receptacle

The Expandable Media Box with Duplex Receptacle/Duplex Surge Suppressor is designed to streamline power and cable management behind your HDTV. The expandable portion of the Media Box allows for maximum storage hidden behind your TV, while still allowing your TV mount to be flush to the wall. This box is available in surge and 20 commercial grade models.