Mono Autoformer In-Wall Volume Control (AVC) Wall Plate - 250W Peak
Same Day Shipping likely on orders placed in the next 00 hours 00 minutes 00 seconds.
California Prop 65 Warning
For CA Residents Only.
California Proposition 65 Warning
Proposition 65, officially the Safe Drinking Water and Toxic Enforcement Act of 1986, is a law that requires warnings be provided to California consumers when they might be exposed to chemicals identified by California as causing cancer or reproductive toxicity. The warnings are intended to help California consumers make informed decisions about their exposures to these chemicals from the products they use. The California Office of Environmental Health Hazard Assessment (OEHHA) administers the Proposition 65 program and publishes the listed chemicals, which includes more that 850 chemicals. In August 2016, OEHHA adopted new regulations, effective on August 30, 2018, which change the information required in Proposition 65 warnings.
• WARNING: Some cable, plastic, and metal products may contain chemicals known to the state of CA to cause cancer, birth defects, or other reproductive harm.
For further information, please visit www.P65Warnings.ca.gov
- Description+
- Features+
- Designed to be Mounted in a Standard Electrical Box
- Autoformers Increase Power Efficiency, Making it an Economical Choice
- Enables a Clutter Free Setup with Wires In-Wall
- One Year Warranty
- Specs+
- 10 Step Attenuation, 30dB Max
- 50W RMS,100W Max Per Channel
- One Gang
- Color: White
- Package Contents+
- (1) AVC Wall Plate
- (2) Matching Color Screws
- Installation Instructions
- Reviews+
- Designed to be Mounted in a Standard Electrical Box
- Autoformers Increase Power Efficiency, Making it an Economical Choice
- Enables a Clutter Free Setup with Wires In-Wall
- One Year Warranty
- 10 Step Attenuation, 30dB Max
- 50W RMS,100W Max Per Channel
- One Gang
- Color: White
- (1) AVC Wall Plate
- (2) Matching Color Screws
- Installation Instructions
Mono Autoformer Volume Control Plate - Wall Plate
Divide and Conquer
Whole-house audio is a new growing trend in home entertainment. It’s never been easier for the average home user to install and configure a system. You can easily run all of your speakers off of a single receiver, but most receivers don’t have a way to control the power coming from an individual channel. You’re stuck with all or nothing. That’s fine if all of your speakers are located in the same room or if you’ve got your own groovy bachelor pad. But when you have to play nicely with others and you’re running your bedroom, living room, and kitchen off of the same receiver, it can be a problem. You’ll quickly find yourself banned from watching football past Little Susie’s bedtime. Volume control wall plates are the ideal solution. They allow you to adjust the volume on a speaker-by-speaker basis.
These Go to Eleven
FireFold’s AVC-MN-WHT mono volume control can definitely do the job. Ten-step attenuation means you can hear all the volume you want without noise or distortion and these controls can handle up to 50 watts RMS per channel with a 250-watt peak. These fit easily into a pre-existing one gang electrical box and they come in a clean white color that easily matches your décor. The built-in auto former, basically a type of low-level transformer, helps condition imperfections from the power stream to ensure you hear the most crystal clear sound possible. Always make sure the maximum output per channel for your receiver doesn’t exceed the maximum for the volume control. If it does, you will have to be careful not to crank the volume knob all the way up.
Installing the AVC-MN-WHT is not much harder than installing any other wall plate. In addition to the wall plate, if you do not already have an electrical box to use, you will need a drywall saw, speaker wire, and a one-gang receptacle box. After cutting the drywall, secure the receptacle box to the stud and fish the speaker wire down into it. Loosen the screws on the input and output then make sure your receiver and amplifier are powered off. Connect the speaker wires to the wall plate then just attach the plate to the box. Once your receiver is back on, you can just turn the knob to increase or decrease the volume.
Mono Autoformer Volume Control Plate - Wall Plate
Divide and Conquer
Whole-house audio is a new growing trend in home entertainment. It’s never been easier for the average home user to install and configure a system. You can easily run all of your speakers off of a single receiver, but most receivers don’t have a way to control the power coming from an individual channel. You’re stuck with all or nothing. That’s fine if all of your speakers are located in the same room or if you’ve got your own groovy bachelor pad. But when you have to play nicely with others and you’re running your bedroom, living room, and kitchen off of the same receiver, it can be a problem. You’ll quickly find yourself banned from watching football past Little Susie’s bedtime. Volume control wall plates are the ideal solution. They allow you to adjust the volume on a speaker-by-speaker basis.
These Go to Eleven
FireFold’s AVC-MN-WHT mono volume control can definitely do the job. Ten-step attenuation means you can hear all the volume you want without noise or distortion and these controls can handle up to 50 watts RMS per channel with a 250-watt peak. These fit easily into a pre-existing one gang electrical box and they come in a clean white color that easily matches your décor. The built-in auto former, basically a type of low-level transformer, helps condition imperfections from the power stream to ensure you hear the most crystal clear sound possible. Always make sure the maximum output per channel for your receiver doesn’t exceed the maximum for the volume control. If it does, you will have to be careful not to crank the volume knob all the way up.
Installing the AVC-MN-WHT is not much harder than installing any other wall plate. In addition to the wall plate, if you do not already have an electrical box to use, you will need a drywall saw, speaker wire, and a one-gang receptacle box. After cutting the drywall, secure the receptacle box to the stud and fish the speaker wire down into it. Loosen the screws on the input and output then make sure your receiver and amplifier are powered off. Connect the speaker wires to the wall plate then just attach the plate to the box. Once your receiver is back on, you can just turn the knob to increase or decrease the volume.